Wall seepage and floor cracks let moisture invade your home year-round. Our certified team in Keshena delivers lasting waterproofing that holds.
Here is what sets our basement waterproofing team apart from the rest.
We design every interior drainage system from scratch based on your basement's actual water entry points, soil type, and floor elevation -- no one-size-fits-all kits.
Porous concrete block and poured walls let groundwater seep through at the mortar joints -- we seal them from the inside with hydraulic cement and crystalline coatings that bond permanently.
Every technician on our crew holds current certification in basement waterproofing systems and participates in ongoing training as products and methods evolve.
Our quotes include the scope of work, materials specified by brand and model, warranty terms, and the payment schedule -- everything you need to compare us fairly.
Most homeowners in Keshena do not realize that a wet basement is not simply a waterproofing problem -- it is a structural warning sign. Hydrostatic pressure that pushes water through walls does not stop pushing when the water is gone. It continues to stress the concrete and masonry, leading to horizontal cracks in block walls, inward bowing of poured walls, and undermining of the footing system. Addressing the symptom without understanding the root cause means spending money on solutions that fail within a few seasons.
Interior drain tile is the most reliable and widely proven basement waterproofing method for existing homes in WI because it manages water that has already entered the wall cavity rather than attempting to stop it at the exterior. The system consists of a perforated pipe, encased in clean washed gravel, installed at or below the footing level in a channel cut along the perimeter of the basement floor. Water that enters the wall-floor joint, seeps through cracks, or migrates through porous concrete flows into this channel and is directed by gravity to a sump basin. A properly sized sump pump then discharges the water away from the foundation. When correctly installed, this system operates indefinitely without clogging because the inlet is protected from sediment by the gravel bed and a filter sock on the pipe.
In poured concrete walls, the most common seepage points are cold joints, tie rod holes, and form tie locations. These are concentrated, well-defined penetrations that respond well to polyurethane or epoxy injection -- a process of drilling small ports along the crack or joint, installing surface-mounted injection ports, and pumping low-viscosity resin under pressure until it fills the void completely. The cured resin is permanently flexible or rigid depending on the product chosen, creating a watertight seal that moves slightly with seasonal concrete expansion without reopening.
Floor cracks are a separate category of water entry that many homeowners underestimate. A hairline crack in a poured concrete floor can transmit significant water when the slab sits on soil with a high water table. Injection of these cracks follows the same principle as wall cracks: drill ports, install fittings, and pump polyurethane resin that expands to fill the void and bond with the surrounding concrete. In situations where the slab has heaved or settled, crack injection is supplemented with undercutting and re-pouring a portion of the slab to restore a flat, properly sealed floor surface.
A complete basement waterproofing system also requires a reliable, properly maintained sump pump installation. We specify sump pits that are large enough to accommodate both a primary pump and a battery backup pump with sufficient separation that the backup does not interfere with the primary float. Discharge lines are routed to daylight at a point that ensures water flows away from the house and cannot recirculate back to the foundation. Battery backup systems are sized to handle a sustained pumping load during a power outage -- not just a brief test cycle -- because the storm events that knock out power are precisely the events that generate the highest water volume in your basement.
Our full-service waterproofing menu addresses every water entry point from foundation wall to window well.
Our drain tile installations use commercial-grade perforated pipe with filter sock protection, gravel bedding, and a concrete topping restored to match your original floor.
We offer both rigid epoxy injection for structural cracks and flexible polyurethane for non-structural shrinkage cracks, matching the right material to the specific crack type and condition.
Sump pits are sized to accommodate both primary and backup pumps without float interference, and discharge lines are routed to a point at least ten feet from the foundation perimeter.
For severe seepage through block walls, we add core-filling with cementitious grout to eliminate the internal cavities that allow water to travel vertically inside the wall system.
Basement floor cracks that allow water infiltration from below are treated with polyurethane injection resin pumped under pressure to fill the void and bond with surrounding concrete.
Failing or undersized window well flashing and frame seals are replaced as part of every window well drainage project to address all water entry paths simultaneously.
We measure moisture levels at multiple points, probe for efflorescence sources, and map every water entry location before recommending any solution.
Our quotes include alternatives at different investment levels so you can choose a phased approach if budget requires it.
All debris is removed daily and the work area is restored progressively so your basement remains usable during multi-day projects.
We perform a complete post-installation inspection, take final moisture readings, and walk you through the system before issuing your written warranty documentation.
After three failed attempts with other companies, JCB Waterproofing and Construction finally fixed our basement for good. The drain system has handled two major rainstorms with zero water in the basement.
Professional from the initial phone call to the final walkthrough. They explained every step of the process and answered every question without making me feel rushed.
I called three companies before choosing JCB Waterproofing and Construction. They were the only ones who actually measured the moisture levels and explained what was causing our specific problem before quoting a fix.
Don't let another wet season damage your foundation. Contact JCB Waterproofing and Construction today for a no-obligation waterproofing assessment in Keshena, WI.
Call +1-866-476-1348 Now